MR32 Flying Cold Saw

What the MR32 flying saw does

Adds wall thickness over MR25 while keeping the same carriage concept. Common on lines that run both decorative tube and small mechanical pipe.

The MR32 sits in the timing belt high speed flying saw category. A positive-drive synchronous belt carries the saw carriage instead of a gear rack. No slip, no re-tensioning, less noise, and a much lighter carriage that reaches speed faster. This is the saw for thin wall, small diameter and high speed lines.

Technical specifications

Model	Round tube OD	Square section	Wall thickness	Line speed	Cut length	Saw blade	Carriage motor	Saw motor	Feed motor
MR32	Ø7.6 – Ø38	6 – 30	0.6 – 2.3	120 / 150	2,000 – 12,000	HSS / TCT Ø350	11 kW servo	7.5 kW	1.8 kW servo

What comes with the machine

Saw carriage — servo driven traverse, sized for the cut length you quote.
Clamping — pneumatic for the small sizes, hydraulic for the heavy wall machines.
Saw head — HSS / TCT Ø350, with the blade tensioner and the cooling arrangement.
Control — servo drive and a controller that holds the cut length within tolerance across the full speed range.
Guard and extraction — enclosed cutting with chip extraction.

Where it is normally installed

Flying saws sit on the exit side of the sizing stand, where the tube has already reached its final dimension and is moving at line speed. That position is what makes the cut square and the length accurate: the saw tracks the moving tube rather than stopping it. We will confirm the station layout with your mill arrangement, including the run-out table and where the cut tube goes afterwards.

All flying saw models

Model	Round tube OD (mm)	Wall thickness (mm)	Line speed (m/min)	Saw blade	Saw motor
MR25	Ø7.6 – Ø25	0.5 – 1.5	120 / 150	HSS / TCT Ø350	5.5 kW
MR32	Ø7.6 – Ø38	0.6 – 2.3	120 / 150	HSS / TCT Ø350	7.5 kW
MR50	Ø20 – Ø63.5	0.8 – 3.0	120 / 150	HSS / TCT Ø400	11 kW
MR60	Ø25 – Ø76	1.0 – 3.5	100 / 120	HSS / TCT Ø450	11 kW
MR76	Ø32 – Ø89	1.2 – 4.5	80	HSS / TCT	15 – 22 kW
MR89	Ø38 – Ø102	1.2 – 4.5	80	HSS / TCT	15 – 22 kW
MR114	Ø63 – Ø114	1.2 – 6.0	70	HSS / TCT	30 kW
MR127	Ø63 – Ø140	1.2 – 6.5	70 / 120	HSS / TCT	30 kW
MR165	Ø76 – Ø168	1.2 – 6.0	60	HSS / TCT Ø600	22 kW servo
MR165 Twin Blade	Ø76 – Ø168	1.5 – 7.0	60	HSS / TCT Ø400	15 kW × 2
MR219	Ø89 – Ø219	2.0 – 8.0	40 – 60	HSS / TCT Ø400	15 kW × 2
MR273	Ø102 – Ø273	2.5 – 12.0	40	HSS / TCT	15 kW × 2
MR377	Ø140 – Ø377	3.0 – 15.0	35	HSS / TCT	22 kW × 2
MR426	Ø102 – Ø426	4.0 – 12.0	40	HSS / TCT	22 kW × 2
MR508	Ø165 – Ø508	3.0 – 16.0	30	HSS / TCT	22 kW × 2

Questions buyers ask about the MR32

What tube sizes does the MR32 cut?

The MR32 cuts round tube from Ø7.6 – Ø38, square section up to 6 – 30 mm and wall from 0.6 to 2.3 mm. Larger sizes and heavier walls move up to the next model in the range.

How fast does it cut?

Line speed 120 / 150 m/min, and the cut length runs from 2,000 – 12,000 mm. Actual length accuracy depends on the encoder, the clamp and the carriage speed being matched to your line speed.

Which saw blade should I use?

HSS / TCT Ø350. HSS is the economical choice for thin wall and general carbon steel; TCT lasts longer and holds an edge better on harder material and thicker wall.

What does the saw motor size mean?

The saw motor is the one doing the cutting. 7.5 kW on this machine, with the carriage on 11 kW servo and feed on 1.8 kW servo. The three are matched as a set; you cannot upgrade one of them on its own.

Can this saw be added to an existing mill?

Yes. Send us the mill model, the tube OD range and the line speed, and we will confirm the foundation, the power supply and the control interface before you commit.

Is this model available with a twin blade arrangement?

The twin blade coordinate type exists for the same size range and is worth considering if your wall is at the heavy end of the specification. We will tell you honestly which one is the better economic choice for your duty.