What tube sizes does the MR25 cut?

The MR25 cuts round tube from Ø7.6 – Ø25, square section up to 6 – 20 mm and wall from 0.5 to 1.5 mm. Larger sizes and heavier walls move up to the next model in the range.

How fast does it cut?

Line speed 120 / 150 m/min, and the cut length runs from 2,000 – 12,000 mm. Actual length accuracy depends on the encoder, the clamp and the carriage speed being matched to your line speed.

Which saw blade should I use?

HSS / TCT Ø350. HSS is the economical choice for thin wall and general carbon steel; TCT lasts longer and holds an edge better on harder material and thicker wall.

What does the saw motor size mean?

The saw motor is the one doing the cutting. 5.5 kW on this machine, with the carriage on 11 kW servo and feed on 1.3 kW servo. The three are matched as a set; you cannot upgrade one of them on its own.

Can this saw be added to an existing mill?

Yes. Send us the mill model, the tube OD range and the line speed, and we will confirm the foundation, the power supply and the control interface before you commit.

Is this model available with a twin blade arrangement?

The twin blade coordinate type exists for the same size range and is worth considering if your wall is at the heavy end of the specification. We will tell you honestly which one is the better economic choice for your duty.

MR25T High-Speed Flying Cold Saw | Ø7.6–Ø25 mm

What the MR25T flying saw does

The smallest and the lightest saw we build. On furniture tube, decorative section and thin-wall conduit the cut cycle is short, and a light carriage that accelerates and decelerates quickly is worth more than extra cutting torque.

The MR25T is the entry point of the timing belt range. A toothed belt drives the carriage along the rail instead of a gear rack, so there is no slip, no periodic re-tensioning and noticeably less noise. The carriage itself is much lighter than a rack version at the same stroke, which is why this saw holds 160 m/min on 0.5 mm wall without marking the tube.

Technical specifications

Model	Round tube OD	Square section	Wall thickness	Line speed	Cut length	Saw blade	Carriage motor	Saw motor	Feed motor
MR25T	Ø7.6 – Ø25	6 – 20	0.5 – 1.5	160	2,000 – 12,000	HSS / TCT Ø350	11 kW servo	5.5 kW	1.3 kW servo

What comes with the machine

Belt-driven carriage — toothed belt on a hardened rail, tensioned at the factory and checked on site.
Clamping — pneumatic on the small sizes, hydraulic from Ø76 upwards.
Saw head — HSS / TCT Ø350, with blade tensioner and coolant arrangement.
Control — servo drive and a controller that holds cut length across the full speed range.
Guard and extraction — enclosed cutting with chip extraction.

Where it is normally installed

The saw sits on the exit side of the sizing stand, where the tube has reached its final dimension and is still moving at line speed. That position is what makes the cut square and the length accurate: the carriage tracks the moving tube instead of stopping it. We confirm the station layout against your mill arrangement, including the run-out table and where the cut tube goes next.

All high-speed flying cold saws

Model	Round tube OD (mm)	Wall thickness (mm)	Line speed (m/min)	Saw blade	Saw motor
MR25T	Ø7.6 – Ø25	0.5 – 1.5	160	HSS / TCT Ø350	5.5 kW
MR32T	Ø7.6 – Ø38	0.6 – 2.3	160	HSS / TCT Ø350	7.5 kW
MR50T	Ø20 – Ø63.5	0.8 – 3.0	150	HSS / TCT Ø400	11 kW
MR60T	Ø25 – Ø76	1.0 – 3.5	150	HSS / TCT Ø450	11 kW
MR76T	Ø32 – Ø89	1.0 – 4.0	120	HSS / TCT	15 – 22 kW
MR89T	Ø38 – Ø102	1.2 – 4.5	120	HSS / TCT	15 – 22 kW
MR114T	Ø50 – Ø114	1.2 – 5.0	120	HSS / TCT	30 kW
MR127T	Ø63 – Ø140	1.2 – 5.5	120	HSS / TCT	30 kW

Questions buyers ask about the MR25T

What tube sizes does the MR25T cut?

Round tube from Ø7.6 to Ø25 mm, square section 6 to 20 mm, rectangular up to 15×25 mm, and wall from 0.5 to 1.5 mm. Above that, move up to the MR32T.

Why is the belt version faster than the rack version?

A toothed belt is a positive drive with very little inertia, so the carriage reaches line speed in a shorter distance and returns faster between cuts. On short cut lengths that is where most of the cycle time is saved.

Can it run continuously at 160 m/min?

Yes, provided the line itself holds 160 m/min and the run-out table is long enough to take the cut tube away. We size the encoder and the clamp to your actual line speed, not to a catalogue figure.

Need roll tooling, a flying cold saw, or a complete tube mill line?