What tube sizes does the MR32 cut?

The MR32 cuts round tube from Ø7.6 – Ø38, square section up to 6 – 30 mm and wall from 0.6 to 2.3 mm. Larger sizes and heavier walls move up to the next model in the range.

How fast does it cut?

Line speed 120 / 150 m/min, and the cut length runs from 2,000 – 12,000 mm. Actual length accuracy depends on the encoder, the clamp and the carriage speed being matched to your line speed.

Which saw blade should I use?

HSS / TCT Ø350. HSS is the economical choice for thin wall and general carbon steel; TCT lasts longer and holds an edge better on harder material and thicker wall.

What does the saw motor size mean?

The saw motor is the one doing the cutting. 7.5 kW on this machine, with the carriage on 11 kW servo and feed on 1.8 kW servo. The three are matched as a set; you cannot upgrade one of them on its own.

Can this saw be added to an existing mill?

Yes. Send us the mill model, the tube OD range and the line speed, and we will confirm the foundation, the power supply and the control interface before you commit.

Is this model available with a twin blade arrangement?

The twin blade coordinate type exists for the same size range and is worth considering if your wall is at the heavy end of the specification. We will tell you honestly which one is the better economic choice for your duty.

MR32T High-Speed Flying Cold Saw | Ø7.6–Ø38 mm

What the MR32T flying saw does

Same frame as the MR25T, one step more wall. It carries 2.3 mm instead of 1.5 mm without a bigger stand, because the belt drive leaves enough headroom in the carriage to absorb it.

The MR32T covers the gap between thin decorative tube and the small structural sizes. Most of the orders we quote on this model are furniture frames, bicycle tube, display shelving and small hydraulic lines, where the tube changes size several times a shift. Tooling changes are quick because the belt carriage parks clear of the pass line and the clamp opens wide enough to thread the next size without re-setting the guides.

Technical specifications

Model	Round tube OD	Square section	Wall thickness	Line speed	Cut length	Saw blade	Carriage motor	Saw motor	Feed motor
MR32T	Ø7.6 – Ø38	6 – 30	0.6 – 2.3	160	2,000 – 12,000	HSS / TCT Ø350	11 kW servo	7.5 kW	1.8 kW servo

What comes with the machine

Belt-driven carriage — toothed belt on a hardened rail, tensioned at the factory and checked on site.
Clamping — pneumatic on the small sizes, hydraulic from Ø76 upwards.
Saw head — HSS / TCT Ø350, with blade tensioner and coolant arrangement.
Control — servo drive and a controller that holds cut length across the full speed range.
Guard and extraction — enclosed cutting with chip extraction.

Where it is normally installed

The saw sits on the exit side of the sizing stand, where the tube has reached its final dimension and is still moving at line speed. That position is what makes the cut square and the length accurate: the carriage tracks the moving tube instead of stopping it. We confirm the station layout against your mill arrangement, including the run-out table and where the cut tube goes next.

All high-speed flying cold saws

Model	Round tube OD (mm)	Wall thickness (mm)	Line speed (m/min)	Saw blade	Saw motor
MR25T	Ø7.6 – Ø25	0.5 – 1.5	160	HSS / TCT Ø350	5.5 kW
MR32T	Ø7.6 – Ø38	0.6 – 2.3	160	HSS / TCT Ø350	7.5 kW
MR50T	Ø20 – Ø63.5	0.8 – 3.0	150	HSS / TCT Ø400	11 kW
MR60T	Ø25 – Ø76	1.0 – 3.5	150	HSS / TCT Ø450	11 kW
MR76T	Ø32 – Ø89	1.0 – 4.0	120	HSS / TCT	15 – 22 kW
MR89T	Ø38 – Ø102	1.2 – 4.5	120	HSS / TCT	15 – 22 kW
MR114T	Ø50 – Ø114	1.2 – 5.0	120	HSS / TCT	30 kW
MR127T	Ø63 – Ø140	1.2 – 5.5	120	HSS / TCT	30 kW

Questions buyers ask about the MR32T

What is the difference between the MR25T and the MR32T?

Wall thickness and maximum section. The MR32T takes 0.6 to 2.3 mm and square up to 30 mm; the MR25T stops at 1.5 mm and 20 mm. The frame and the drive are the same.

Does the larger wall slow the line down?

No. Both models run 160 m/min. The saw motor steps up from 5.5 kW to 7.5 kW so the blade keeps its surface speed on the heavier wall.

Can I cut square and rectangular tube on the same saw?

Yes, with the square clamp option. Square 6 to 30 mm and rectangular up to 20×40 mm run on the same blade and the same clamp body.

Need roll tooling, a flying cold saw, or a complete tube mill line?