What tube sizes does the MR50 cut?

The MR50 cuts round tube from Ø20 – Ø63.5, square section up to 15 – 50 mm and wall from 0.8 to 3.0 mm. Larger sizes and heavier walls move up to the next model in the range.

How fast does it cut?

Line speed 120 / 150 m/min, and the cut length runs from 2,000 – 12,000 mm. Actual length accuracy depends on the encoder, the clamp and the carriage speed being matched to your line speed.

Which saw blade should I use?

HSS / TCT Ø400. HSS is the economical choice for thin wall and general carbon steel; TCT lasts longer and holds an edge better on harder material and thicker wall.

What does the saw motor size mean?

The saw motor is the one doing the cutting. 11 kW on this machine, with the carriage on 11 kW servo and feed on 1.8 kW servo. The three are matched as a set; you cannot upgrade one of them on its own.

Can this saw be added to an existing mill?

Yes. Send us the mill model, the tube OD range and the line speed, and we will confirm the foundation, the power supply and the control interface before you commit.

Is this model available with a twin blade arrangement?

The twin blade coordinate type exists for the same size range and is worth considering if your wall is at the heavy end of the specification. We will tell you honestly which one is the better economic choice for your duty.

MR50T High-Speed Flying Cold Saw | Ø20–Ø63.5 mm

What the MR50T flying saw does

The volume model of the belt range. Around Ø51 to Ø63.5 is where furniture tube, ventilation duct and galvanised conduit overlap, and this is the saw that runs that mix every day.

A Ø400 blade and an 11 kW saw motor give the MR50T enough blade speed to cut 3 mm wall cleanly, while the belt carriage still holds 150 m/min. The clamp is pneumatic as standard on this size, which keeps the clamp time short enough to match the line speed on thin wall. Hydraulic clamping is available where the wall runs at the top of the range.

Technical specifications

Model	Round tube OD	Square section	Wall thickness	Line speed	Cut length	Saw blade	Carriage motor	Saw motor	Feed motor
MR50T	Ø20 – Ø63.5	15 – 50	0.8 – 3.0	150	2,000 – 12,000	HSS / TCT Ø400	11 kW servo	11 kW	1.8 kW servo

What comes with the machine

Belt-driven carriage — toothed belt on a hardened rail, tensioned at the factory and checked on site.
Clamping — pneumatic on the small sizes, hydraulic from Ø76 upwards.
Saw head — HSS / TCT Ø400, with blade tensioner and coolant arrangement.
Control — servo drive and a controller that holds cut length across the full speed range.
Guard and extraction — enclosed cutting with chip extraction.

Where it is normally installed

The saw sits on the exit side of the sizing stand, where the tube has reached its final dimension and is still moving at line speed. That position is what makes the cut square and the length accurate: the carriage tracks the moving tube instead of stopping it. We confirm the station layout against your mill arrangement, including the run-out table and where the cut tube goes next.

All high-speed flying cold saws

Model	Round tube OD (mm)	Wall thickness (mm)	Line speed (m/min)	Saw blade	Saw motor
MR25T	Ø7.6 – Ø25	0.5 – 1.5	160	HSS / TCT Ø350	5.5 kW
MR32T	Ø7.6 – Ø38	0.6 – 2.3	160	HSS / TCT Ø350	7.5 kW
MR50T	Ø20 – Ø63.5	0.8 – 3.0	150	HSS / TCT Ø400	11 kW
MR60T	Ø25 – Ø76	1.0 – 3.5	150	HSS / TCT Ø450	11 kW
MR76T	Ø32 – Ø89	1.0 – 4.0	120	HSS / TCT	15 – 22 kW
MR89T	Ø38 – Ø102	1.2 – 4.5	120	HSS / TCT	15 – 22 kW
MR114T	Ø50 – Ø114	1.2 – 5.0	120	HSS / TCT	30 kW
MR127T	Ø63 – Ø140	1.2 – 5.5	120	HSS / TCT	30 kW

Questions buyers ask about the MR50T

Pneumatic or hydraulic clamp on the MR50T?

Pneumatic is the standard for 0.8 to 2.0 mm wall. Above 2 mm, or where the tube surface is critical, we quote the hydraulic clamp instead.

What blade does it use?

HSS or TCT Ø400. HSS is cheaper per blade and fine on mild steel; TCT lasts longer on galvanised and on high-strength tube.

What line speed should I expect?

150 m/min. That is the belt limit for this carriage mass, and it is the figure we hold the cut length tolerance to.

Need roll tooling, a flying cold saw, or a complete tube mill line?