What tube sizes does the MR89 cut?

The MR89 cuts round tube from Ø38 – Ø102, square section up to 70 × 70 mm and wall from 1.2 to 4.5 mm. Larger sizes and heavier walls move up to the next model in the range.

How fast does it cut?

Line speed 80 m/min, and the cut length runs from 3,000 – 12,000 mm. Actual length accuracy depends on the encoder, the clamp and the carriage speed being matched to your line speed.

Which saw blade should I use?

HSS / TCT. HSS is the economical choice for thin wall and general carbon steel; TCT lasts longer and holds an edge better on harder material and thicker wall.

What does the saw motor size mean?

The saw motor is the one doing the cutting. 15 – 22 kW on this machine, with the carriage on 15 kW servo and feed on 2.9 kW servo. The three are matched as a set; you cannot upgrade one of them on its own.

Can this saw be added to an existing mill?

Yes. Send us the mill model, the tube OD range and the line speed, and we will confirm the foundation, the power supply and the control interface before you commit.

Is this model available with a twin blade arrangement?

The twin blade coordinate type exists for the same size range and is worth considering if your wall is at the heavy end of the specification. We will tell you honestly which one is the better economic choice for your duty.

MR89T High-Speed Flying Cold Saw | Ø38–Ø102 mm

What the MR89T flying saw does

The practical upper end of the belt range. At Ø102 and 4.5 mm wall a rack machine starts to be the cheaper answer, and we say so on the quotation rather than selling the faster saw.

The MR89T exists for one combination: large diameter with thin wall, where the line speed matters more than the cutting torque. Structural tube, scaffold and general fabrication at 1.2 to 4.5 mm fall into that bracket. Above 4.5 mm, or where the mill runs slower anyway, the MR89 in the rack range costs less and cuts just as square.

Technical specifications

Model	Round tube OD	Square section	Wall thickness	Line speed	Cut length	Saw blade	Carriage motor	Saw motor	Feed motor
MR89T	Ø38 – Ø102	30 – 80	1.2 – 4.5	120	2,000 – 12,000	HSS / TCT	15 kW servo	15 – 22 kW	2.9 kW servo

What comes with the machine

Belt-driven carriage — toothed belt on a hardened rail, tensioned at the factory and checked on site.
Clamping — pneumatic on the small sizes, hydraulic from Ø76 upwards.
Saw head — HSS / TCT, with blade tensioner and coolant arrangement.
Control — servo drive and a controller that holds cut length across the full speed range.
Guard and extraction — enclosed cutting with chip extraction.

Where it is normally installed

The saw sits on the exit side of the sizing stand, where the tube has reached its final dimension and is still moving at line speed. That position is what makes the cut square and the length accurate: the carriage tracks the moving tube instead of stopping it. We confirm the station layout against your mill arrangement, including the run-out table and where the cut tube goes next.

All high-speed flying cold saws

Model	Round tube OD (mm)	Wall thickness (mm)	Line speed (m/min)	Saw blade	Saw motor
MR25T	Ø7.6 – Ø25	0.5 – 1.5	160	HSS / TCT Ø350	5.5 kW
MR32T	Ø7.6 – Ø38	0.6 – 2.3	160	HSS / TCT Ø350	7.5 kW
MR50T	Ø20 – Ø63.5	0.8 – 3.0	150	HSS / TCT Ø400	11 kW
MR60T	Ø25 – Ø76	1.0 – 3.5	150	HSS / TCT Ø450	11 kW
MR76T	Ø32 – Ø89	1.0 – 4.0	120	HSS / TCT	15 – 22 kW
MR89T	Ø38 – Ø102	1.2 – 4.5	120	HSS / TCT	15 – 22 kW
MR114T	Ø50 – Ø114	1.2 – 5.0	120	HSS / TCT	30 kW
MR127T	Ø63 – Ø140	1.2 – 5.5	120	HSS / TCT	30 kW

Questions buyers ask about the MR89T

When should I choose the rack machine instead?

When the wall goes above 4.5 mm, or when the mill itself runs below about 80 m/min. The belt premium only pays back if you actually use the higher line speed.

What is the largest square section?

80 mm square and 50×100 mm rectangular. Larger sections move to the rack range, where the clamp force is higher.

Does the longer carriage affect floor space?

Yes, slightly. The belt carriage needs a longer rail than a rack carriage at the same stroke. We send the footprint drawing with the layout.

Need roll tooling, a flying cold saw, or a complete tube mill line?